On my system, the file is in: ~/ports/devel/fie-mono-64 but again, I'd suggest modifying it to better suit your needs. The commented content of the portfile is intentionally commented. The intention was to get the portfile building and deploying 64 bit mono in as simple and supported a way as possible. A lot of the way macports had been building mono seemed to be older cruft from less mac friendly versions of mono. I half expected to have to put them back in. So I left them commented. But so far, no issues have popped up. -brad On Jun 20, 2013, at 11:53 AM, Alon Dulce <alondu@gmail.com> wrote:
Hi,
I tried using the portfile attached without success, are all the commented lines supposed to be commented ? I did the following steps:
1. I setup a folder for my local macports "~/Documents/Loc_Macports/" 2. Inside this folder I set up the directory structure according to what I understood from the port file attached: "~/Documents/Loc_Macports/devel/lang/mono/" and put the portfile in that folder 3.I didn't see any patch files in the port file (all are commented) - so I didn't do anything regarding this. 4. I edited the source.conf file with : open -a TextEdit /opt/local/etc/ports/sources.conf and added before the following line: file:///Users//~/Loc_Macports/
before this line :
rsync://rsync.macports.org/release/tarballs/ports.tar [default]
5. I indexed my local repository: portindex ~/Documents/Loc_Macports/
But i received notification that none were indexed and here I'm stuck.
Any insights ?
BR, Alon.
---------- Forwarded message ---------- From: brad@fie.us <brad@fie.us> Date: Fri, Jun 14, 2013 at 2:01 AM Subject: Re: [Python.NET] running pythonnet on MAC OSX[new to MAC and not not a programmer] To: Alon Dulce <alondu@gmail.com> Cc: pythondotnet@python.org
So, firstly, I build my own 64bit mono. In that last thread, I said I was doing it off of their tar ball.
I updated that slightly. I now maintain my own local "mac ports" port file.
Attached is the latest one I built. It may need updating. And at the very least, you probably want to update it to build into a different place than my company's directory on my systems.
Once it's built, it does create it's own pkg-config directory so you can use it in building python-net
You can try and build against the usual 32-bit mono distributions on OSX. But it's usually a bad idea. Python is usually 64-bit in most places you'd want to use it in OSX. When Xamarin finally gets around to fully distributing in 64-bit on OSX by default, things will be easier and this part won't be necessary.
On Jun 12, 2013, at 10:35 AM, Alon Dulce <alondu@gmail.com> wrote:
Hi,
I want to run python.NET on MAC OSX (Mountain Lion) and since I'm new to MAC/UNIX and I'm not a programmer I naturally turned to the web:
*1st : I tried iron python using eclipse with MONO (configuring eclipse iron python interpreter to the mono framework "/Library/Frameworks/Mono.framework/Versions/icy" file) - eclipse doesn't allow this and I got the following error:
"No output was in the standard output when trying to create the interpreter info."
*2nd : I tried python.NET on XAMARIN :
I found this link: http://curtis.schlak.com/2012/01/17/howto-run-pythonnet-on-osx.html
I followed all the instructions but it's not clear to me how can I write python in XAMARIN, import clr etc. (I set up the solution as explained in the link above but I'm not sure about the next step).
* 3rd try : I found a post on this mailing list : http://mail.python.org/pipermail/pythondotnet/2011-September/001171.html
I tried using the original makefile and setup.py (both makefiles) with "sudo setup.py install" and received the following error: "dyld: DYLD_ environment variables being ignored because main executable (/usr/bin/sudo) is setuid or setgid /bin/sh: pkg-config: command not found Traceback (most recent call last): File "setup.py", line 46, in <module> argsDict = pkgconfig('glib-2.0', 'mono-2') File "setup.py", line 32, in pkgconfig raise RuntimeError("An error has occured") RuntimeError: An error has occured "
I also tried editing the makefiles and setup.py according to the diff file supplied in the thread but still no success.
Is there a makefile/ setup.py file that will work on MAC ? maybe some sort of step by step monkey guide... :-)
I appreciate the help, Alon. _________________________________________________ Python.NET mailing list - PythonDotNet@python.org http://mail.python.org/mailman/listinfo/pythondotnet
<Portfile>